2022-02-15 18:40:23
G1 BMS system user manual which documents the whole BMS system components, connectivity, configuration, monitoring, troubleshooting and much more.
Download Release NotesAdded new chapters:
2.1.3 Centralized Cell Monitoring
2.1.4 Temperature measurement
2.3.2 Integrated SOC/SOH estimator (gen1 algorithm)
2.3.2.1 SOH algorithm
2.7 Warnings
4.1 EMUS BMS Control Panel
4.9 Charging process
4.14 SOC Estimation
4.14.1 SOC legacy adjustment algorithm
4.14.2 SOC/SOH estimator (gen1 algorithm)
4.14.2.1 Tuning parameters
4.14.2.2 Cell model reference settings
4.14.2.3 SOC-OCV dependency curve of cell
4.14.2.4 SOC dependency on temperature
Other:
All products technical information has been transferred to separate datasheet documents
2021-01-28 15:32:49
Download Release Notes2021-05-13 16:18:53
Download Release NotesKnown issues:
When tabs that were dragged out of the main window are closed, the whole Control Panel can also close
Pulses per Distance Unit field is unused for now as Speed Sensor input is not functioning yet
GPI, GPO selection list not fully correct
User interface does not allow to enter high accuracy PSU divider value
Min User SoC range can be set higher than Max. Then user SoC is shown as 0% or 100%
2022-02-15 18:23:43
Download Release Notes#7662 DC/DC Zero Current Control
#7782 Manual control of J1939 charger IDs. Note: Elcon name changed to J1939
#6380 Added support for LTO cells
#7734 Added support for Cell Wire Break functionality
#7892 Added new set Battery ID feature
Added new EMUS CAN devices support for CGM022 and TES011
Cell Module version now can be seen in Control Panel in Cells Tab
#7758 Fix to External Temperature Sensor Calibration
#7857 Fix to Auto Connection issue
#7770 Fix to drag'n'drop issue while configuring CCGMs/CGMs
#8094 When wire break is found the individual cell voltage shown in cells tab is not accurate
#7474 Battery Charge/Capacity not recalculated/displayed in legacy firmware
#7475 PSU input/output does not function correctly
#7484 No warning/message when password is typed in incorrectly more than 10 times
2021-09-24 17:13:51
Firmware for EMUS BMS Mini devices.
Download Release NotesKnown issues:
Non-Clearable statistics not saved
BMS might reset during charging stages, reset period could be 1-2hrs
Wireless connectivity module only transmits data to a connected device, receiving will be added in a later firmware update
Main clock can drift and fall behind up to couple of minutes per day
Speed Sensor input is not functioning yet
No SoC PWM output functionality yet
Cell Wire Break protection deactivation delay is not as set
BMS reset needed after cell count configuration to clear wire break protection/indication
CAN Broadcast Period not accurate
Each Call Value not broadcasted
Charging restarts on max cell voltage drops below restart value
Out of boundary current is indicated as measured, not as incorrect reading
Wire break indicated correctly not in all cases
Version 2.8.4Known issues:
Wireless connectivity module only transmits data to a connected device, receiving will be added in a later firmware update
Main clock can drift and fall behind up to couple of minutes per day
Speed Sensor input is not functioning yet
No SoC PWM output functionality yet
Cell Wire Break protection deactivation delay is not as set
BMS reset needed after cell count configuration to clear wire break protection/indication
2022-02-15 18:24:59
Download Release Notes#7649 Cell Wire Break detection functionality
#6377 LTO cell support (v2.9.1)
#7993 No communication error fix
---
2022-03-29 14:05:49
Download Release Notes#8148 SOC algorithm fix
#8094 When wire break is found some voltage calculations might not be fully correct
#8095 Wire break detection for LTO cells with higher voltages (~3.4V) is not accurate
#7485 In some situations entering L2 access (when L2 password is not set) can be complicated
2020-05-26 18:39:31
Download Release NotesFixes
Value of 'Total Voltage' in Layout #4 was displayed incorrectly above 655 volts
2019-06-18 16:55:43
Download Release NotesFixes
Value of 'Total Voltage' in Layout #4 was displayed incorrectly above 655 volts
2019-04-02 17:04:49
Download Release NotesFeatures
Default layout
This feature allows user to select desired display layout, which persist after power reset.
Ignition Sense
Display preview state will be controlled by ignition input status. When ignition input status becomes inactive - display is turned off and vice-versa. "Ignition" pin-function must be mapped in Control Unit
2018-11-11 17:51:14
Download Release Notes2018-11-11 17:49:26
Download Release Notes2019-02-11 17:36:44
Notifications of End of Life announcement of EMUS products . For full history list of EoL notifications please press "Show all Versions" at the bottom.
Download2019-02-11 17:37:55
Notifications of EMUS products price changes. For full history list of price update notifications press "Show all Versions" at the bottom.
Download2019-10-01 08:20:57
Detailed description of G1 BMS CANopen Object Dictionary
Download2021-11-03 18:27:48
Download Release Notes2018-12-10 10:34:09
Download Release NotesOur company specialists are ready to provide technical assistance and consult in matters related with use of our products. In order to attain the best service quality, we kindly ask you to fill the contact form by clicking the button below.